Updated HPE0-S58 Dumps V9.02 Is Good For HPE Composable Infrastructure Exam

1. During an initial setup of a Synergy environment, an integrator needs to enable or disable authorized Service access.

What will be the outcome when the integrator disables this service?

2. FILL BLANK

A customer has the following configuration:

Frame 1

- Bay 1 C HPE Synergy 12Gb SAS Connection Module

- Bay 2

- Bay 3 C HPE Virtual Connect SE 40 GB F8 Module

- Bay 4 C HPE Synergy 12GB SAS Connection Module

- Bay 5

- Bay 6 C HPE Synergy 10 Gb Interconnect Link Module

Frame 2

- Bay 1 C HPE Synergy 12Gb SAS Connection Module

- Bay 2

- Bay 3 C HPE Synergy 10Gb Interconnect Link Module

- Bay 4 C HPE Synergy 12Gb SAS Connection Module

- Bay 5

- Bay 6 C HPE Virtual Connect SE 40Gb F8 Module

How many more frames can the customer add to their Synergy composable fabric? (Note: Enter your answer in the answer field below.)

3. In a 3-frame HPE Synergy environment, how should an integrator place the image Streamer modules to allow for redundancy to all of the management connections?

4. What must an integrator do before an existing cluster can be imported to the HPE Composer?

5. Refer to the exhibit.

How should an integrator pair interconnect bays to set up redundant fabrics in an HPE Synergy 12000 Frame?

6. Refer to the exhibit.

An integrator needs to add an FCoE connection to the server profile, but the FCoE connection type is not available.

What is the likely cause of this issue?

7. An integrator is installing three Synergy frames in different locations for a customer. As part of the installation, the customer requests a single monitoring dashboard that shows the current hardware status, warranty status, and open support cases of all three frames.

Which configuration steps must the integrator perform to provide the customer with this functionality?

8. What are valid uses for an IPv4 address pool when configuring an HPE Synergy solution? (Choose two.)

9. HOTSPOT

A customer has the following HPE Synergy solution:

- three Synergy frames

- two HPE Virtual Connect SE 32Gb Fibre Channel (FC) modules in each time

- two HPE Virtual Connect SE 40GB F8 modules

- four HPE Synergy 10Gb Interconnect Link Modules

Click the menu option the integrator should use to add more uplinks ports from HPE Virtual Connect SE 32 Gb FC modules to SAN uplink set.

10. Which policy can an integrator apply when creating a datastore using HPE OneView for vCenter Server?

11. An integrator prepares deployment documents with the list of all the hardware and software components. The integrator also needs a list of all infrastructure services deployed, with the functionality described.

Which services are provided by the vCenter Server component and should be placed in the report? (Choose two.)

12. A customer needs to evaluate Image Streamer as Proof-of-Concept (PoC) in a test and development tab environment.

At a minimum, what does a Synergy integrator need in order to support this requirement?

13. Which component of the HPE Synergy solution should you use to set the firmware/driver baseline and the installation method for Synergy Compute nodes?

14. Which storage solution can be used for volume provisioning using HPE Composer?

15. What is the purpose of the OmniStack Accelerator card installed in HPE SimpliVity platform?

16. A customer needs to deploy a farm of Windows Server 2019 Hyper-V using an Image Streamer. The customer discovered that the OS Build Plan for this OS is not available from the Image Streamer interface.

How can the customer access all the tools and scripts needed to provision the required operating system?

17. HOTSPOT

An integrator has installed a new Synergy frame into a rack with two existing Synergy frames in a customer’s environment.

Click where the integrator should verify that the cabling for the management ring was completed correctly.

18. A customer needs to aggregate uplink ports from two Virtual Connect interconnects to increase bandwidth and availability of the networks configured for HPE Synergy platform.

Which steps must the integrator perform in the configuration to meet the customer’s needs?

19. Which operating systems are supported for use with Image Streamer? (Choose two.)

20. An HPE Synergy compute module has a template-based server profile with two identically configured connections, each containing five VLANs.

What is the most efficient method the integrator can use to add a new VLAN to each connection?

21. HOTSPOT

An integrator needs to validate whether the datastore created for ESXi systems based on 3PAR virtual volume can support all DRS cluster functionalities.

Click on the parameter that the integrator needs to verify.

22. A customer needs to significantly improve I/O performance to a database server.

Which product should an integrator implement as part of a Synergy composable solution?

23. A customer tries to revert a data volume located on the HPE 3PAR array to a specific snapshot that was taken using HPE Composer, but the process fails.

What must an integrator do to fix this problem?

24. DRAG DROP

Match each HPE server platform with optimal workload.

25. A customer needs to deploy additional management components, such as vCenter Server and HPE Global Dashboard.

According to HPE best practices, how should an integrator deploy these components?

26. During a first-time installation of HPE Synergy, an external monitor is not available to the integrator.

Which approach should the integrator take to perform the first-time setup?

27. A customer has a datacenter with 3-frame Master/Satellite Synergy solution. They plan to add two additional frames to the remote datacenter, but they want to have a single management tool.

How should the integrator set up the management of the datacenter?

28. An integrator needs to configure a set of networks for Synergy compute nodes to send data to devices outside of a Synergy frame.

How should the integrator complete the task?

29. A customer needs to expand a single-frame Synergy solution to two frames.

What should the integrator do to establish a proper management network for the two frames?

30. A customer is planning an HPE Synergy solution with 20 frames and needs to minimize the number of management ports that are required to connect the frames into the existing management network.

Which procedure should the integrator use to address the customer’s concern?