Updated D-PSC-MN-01 Dumps (V9.02) – Ensure Your Success in the Dell PowerScale Maintenance Version 2 Exam on the First Try

1. A customer notices a platform engineer intentionally leaving a 1U gap underneath a Dell PowerScale H400 chassis during racking and stacking What is the purpose of the gap?

2. Which cluster interface provides the most detailed network traffic statistics and enables file and directory operations on the cluster?

3. A platform engineer is connecting a new Dell PowerScale F600 node to the frontend switch in an existing cluster with legacy nodes.

How should the network cables be connected?

4. A platform engineer connected to a Dell PowerScale F600 node using a serial connection. The session is unresponsive.

What action must the engineer take?

5. DRAG DROP

A platform engineer is creating a Dell PowerScale cluster using the Configuration Wizard. They have selected the Create a new cluster option.

What Is the correct sequence of steps to create the cluster?

6. A platform engineer must replace a failed chassis on a Dell PowerScale Gen6 cluster.

What must the engineer do after powering off the nodes?

7. Dell Technical Support has requested a part be sent back to Dell Logistics to be studied.

Which process or document musi be completed before sending the part back?

8. What must be enabled in SMB to ensure nondisruptive upgrades?

9. Windows clients cannot connect using the fully qualified domain name when testing the connectivity of a newly created cluster.

What connection test identifies the problem?

10. An engineer runs ini_reformat_node command.

What are they attempting to do?

11. An existing PowerScale cluster consists of four A300 and three F600 nodes.

What is the minimum number of nodes an engineer can add to expand both node pools?

12. What type of upgrade on a Dell PowerScale cluster requires the least amount of time?

13. Refer to the exhibit.

An engineer replaced the drive in C1. They run the isi devices drive list command and obtain the output that is shown.

What action must the engineer take?

14. What is the isi diagnostics gather command used for?

15. Which model is a part of the Isilon Gen6 platform?

16. What is done with the components when a Gen6 single node is replaced?

17. What does a terracotta colored handle indicate on Dell PowerScale Gen6 hardware?

18. What is the rack size of an F600 node?

19. What type of NIC can be used for the external network on a Dell PowerScale F600 node?

20. Which resource should be consulted before performing any Dell PowerScale platform maintenance activities?

21. Which two backend switches support 100 GbE?

A. DCS-7308

B. S5232-ON

C. 29264-ON

D. D4040

22. What must be replaced at the same time the backup battery is replaced?

23. An engineer replaced a failed node in a PowerScale H500 due to hardware issues. They must verity that the replacement node is functioning correctly.

What is a crucial step when replacing the failed node in the cluster?

24. What status is an engineer trying to test if they run the isi_hwmon -s command?

A. DIMM

B. Sensor

C. CPU

D. Battery

E. System

25. A platform engineer must install several Dell PowerScale clusters.

Which rack should they use for the A3000 nodes?

26. Which port slot provides management functionality on a PowerScale F600?

27. DRAG DROP

What Is the correct order of steps to Install a PowerScale Gen6 in a rack?

28. Exhibit.

A platform engineer has connected power cables to a Dell PowerScale Gen6 node.

What does the status indicator indicate?

29. A platform engineer does not have a Flash drive available.

How can they reimage a Dell PowerScale node?

30. What type of drive should a customer use to ensure that their data is encrypted?

A. NVMe

B. SSD

C. SED

D. Hard drive

31. What can be viewed using the isi_upgrade_logs _s command?

A. Post upgrade errors

B. Current upgrade state

C. Active upgrade errors

D. Upgrade assessment results

32. What is an important consideration when connecting Dell PowerScale Gen6 nodes to external power?

A. Cable each node in a node pair to a different PDU.

B. Cable all nodes to the external power feeds before connecting switch power cables.

C. The total power load for all nodes in the rack should not exceed 100% of the branch circuit rating.

D. Connect both cables of each node to different external power feeds.

33. Which three F200 components can a customer replace?

A. System Battery

B. Network Interface Card

C. CPU module

D. DIMM

E. NVDIMM Battery

34. A customer is planning to expand a Dell PowerScale Gen5 cluster with H500 nodes What is a consideration?

35. An engineer wants to create a 4-node cluster after rack and stack.

What port must they use to start the installation?