Service Provider Routing and Switching, Professional (JNCIP-SP) JN0-663 New Dumps

1. Exhibit:

Referring to the exhibit, hosts in Site 1 and Site 2 are unable to communicate with each other through the Layer 3 VPN.

What is the problem?

2. Which two statements regarding Ethernet segments (ES) are correct? (Choose two)

3. Exhibit.

Referring to the exhibit, there is an Layer 3 VPN setup that connects sites CE-A-1. CE-A-2 and CE-A-3 together Host-1 can communicate with Host-3. but Host-1 cannot communicate with Host-2

What must you do to solve the problem?

4. Exhibit:

Referring to the exhibit, which path would traffic passing through R1 take to get.

5. Exhibit.

You are providing camer-of-carner VPN services for AS 100 and AS 200 You want to distribute MPLS labels between your PE routers and the AS 100 and AS 200 CE routers.

What must be enabled to accomplish this task?

6. You are asked to configure a series of interface policers and firewall filters, which include policers, on the same device You must ensure that the two configuration methods do not conflict.

What are two considerations when performing this task? (Choose two.)

7. Exhibit.

You are using EVPN to provide Layer 2 stretched VLANs between two sites You notice that the MAC addresses in either site are not showing up on the remote site.

Referring to the exhibit, what are two ways to solve this problem? (Choose two)

8. You are creating an LDP-signaled Layer 2 circuit between two sites. Site1 and Site2 use different VLAN IDs to connect to your PE devices In this scenario, which encapsulation type must be used on the logical interfaces?

9. Which two statements about IS-IS are correct? (Choose two.)

10. You are responsible for configuring CoS for your network Your network includes a video application with strict latency requirements, so that any packets delayed by more than 75 ms are effectively useless. You want to ensure that you do not waste buffer space.

When configuring the scheduler for this application, which feature would you use?

11. Exhibit: Referring to the exhibit, you want to make ISP1 your preferred connection for inbound and outbound traffic.

Which two steps will accomplish this task? (Choose two.)

12. Click the Exhibit button.

A network administrator is investigating why traffic from R2 is not being forwarded to R1

Referring to the show isis database command output shown in the exhibit, what is causing this problem on the network?

13. Exhibit:

Referring to the exhibit, which statement is true?

14. Exhibit:

R1 assigns incoming voice traffic to the ef forwarding class. All other traffic is assigned to the best-effort forwarding class You have configured a CoS re-write rule on R1 to include the correct CoS bit values in packets sent towards R2 You want R2 to classify traffic using the CoS markings created by R1.

Which two configuration steps are necessary to accomplish this task? (Choose two.)

15. Exhibit:

You notice an inconsistency between the routing table and the OSPF database, as shown in the exhibit.

What are two reasons for this behavior? (Choose two.)

16. Exhibit:

A network administrator is concerned about the number of LSAs that they are observing on the network.

What will reduce Type 7 LSAs advertised from R2 to the non-backbone routers shown in the exhibit?

17. The link between CE1 and PE1 has a history of flapping To avoid the impact that flapping causes to the network you decide to use route damping

Which statement is correct in this scenario?

18. Exhibit.

You are troubleshooting a problem with a BGP peer where BGP routes are not being accepted from that peer.

Referring to the exhibit, which two statements are correct*? (Choose two)

19. Exhibit:

Which three statements are true about the show pim join output shown in the exhibit? (Choose three.)

20. Exhibit:

R2 is receiving a route from R1 and you must ensure that the route is not advertised to R3.

Referring to the exhibit, which two configurations on R2 will solve the issue? (Choose two.)

21. What information is stored in a VRF table for a BGP Layer 2 VPN? (Choose three.)

22. You want to allow the load balancing of traffic for an EBGP route from two different peers in the same AS.

Which three actions are needed to accomplish this task? (Choose three.)

23. Exhibit.

Two CE devices (CE-1 and CE-2) belong to the same customer and connect into a single PE device (PE-1) However, the CE devices cannot communicate with each other. You want to allow the CE devices to communicate with each other.

Referring to the exhibit, which action would solve the problem?

24. Exhibit: Referring to the exhibit, the local BGP router is receiving IPv4 routes from the BGP neighbor, but it is not receiving L3 VPN routes from the BGP neighbor.

Which two actions should you take to solve this problem? (Choose two.)

25. What is the purpose of the duster-list attribute within a BGP route reflector group?

26. Exhibit.

You are provisioning Layer 2 circuits between sites CE1. CE2. andCE3

Referring to the exhibit, which statement is true?

27. Exhibit.

You have the LDP signaled VPLS topology as shown in the exhibit CE-B at Site-2 is multihomed to both PE-2 and PE-3

In this scenario where would you configure loop prevention?

28. You are deploying a new EVPN service for your customers.

You must build the service based on the following requirements

-- both Layer 2 and Layer 3 functionality must be supported

-- your customers must be able to support multiple VLANs in the same EVPN instance (EVI).

In this scenario which two types of routing instances should be configured? (Choose two.)

29. Exhibit:

Traffic is being sent from R2 to R3. The link between R2 and R3 fails.

Referring to the exhibit, which statement is correct?

30. Exhibit:

Referring to the exhibit, which two statements are true? (Choose two.)