Nutanix Certified Services Consultant (NCSC): Level 1 NCSC Level-1 Exam Dumps

1. Which subnet is reserved for internal connectivity within a Nutanix Cluster?

2. A customer has an ESXi Cluster with two 10GbE NICs on each node with the following requirements:

* Solution must follow Nutanix Best Practices

* Network configuration should be redundant

* A vSphere Standard Switch must be utilized

Which load balancing method should be used?

3. A customer wants to know the details of network validation testing.

Where can the consultant find this information?

4. A consultant creates an AHV cluster and connects the Intel X550T NICs to the top of rack switch using Twinax cables. The activity and link lights are green. The cluster cannot communicate over the 10GbE link.

What is the first command the consultant should perform to troubleshoot the issue?

5. A consultant is viewing an ESXi host via console without external network connectivity.

Which two IP addresses can be used to connect to the CVM (Choose two.)

6. A consultant is setting up a new vSphere cluster. Customer requirements are as follows:

* VMs should automatically failover to another host if the host crashes

* Host CPU and Memory resources should be evenly balanced

* New VMs should be placed on the host with the most resources available

Which two settings should be turned on to meet the requirements? (Choose two.)

7. A consultant is planning an installation and needs to collect configuration items to be used during the install. The data needed from the customer are IP addresses, Gateway, DNS servers, and NTP Servers.

Which Cluster Deployment document must be completed with the customer?

8. A consultant creates a Windows VM after installing a new Nutanix cluster running AHV. The consultant has statically assigned an IP address to the VM but it is unable to communicate on the network.

Which action should the consultant take to resolve this issue?

9. A consultant is onsite with a customer running Foundation VM (FVM) and discovers that

there is no connectivity between the FVM and their laptop.

The consultant verifies the following:

* The consultant’s laptop and Nutanix nodes are plugged into a flat switch.

* The laptop, switch and nodes are plugged into supported power supplies.

* The laptop network adapters and FVM are configured with their corresponding IP addresses.

What is the cause for the connectivity failure to the FVM?

10. A customer would like to re-image an existing cluster. The Foundation Applet and Foundation VM is unavailable to them.

How can the consultant access Foundation-as-a-Service (FaaS)?

11. After a recent installation using a flat switch, a consultant notices issues migrating the Nutanix nodes to the customer’s network. The customer states that they are using VLANs on the production switch but not on the dedicated switch for IPMI. The customer does not require a manual configuration of the host and CVM.

What network changes need to be made to correct the issues?

12. A consultant has deployed a new Nutanix AHV cluster with Foundation. The customer requests separating the management and production traffic in the CVM.

Which feature should the consultant configure?

13. Where in the Support Portal is the Best Practices guide for vSphere Networking located?

14. A Nutanix cluster has 10TB usable storage. The customer wants to create a 100GB datastore for ISO images to eliminate too much storage being consumed by unnecessary images.

Which setting should be used to accomplish this goal?

15. A consultant is preparing to add new nodes into an existing cluster. The current cluster AOS version is 5.8. The new expansion node is currently running AOS 5.9 code. The cluster must continue to run at its current AOS version.

Which method can be used to successfully add the node?

16. Where can a consultant find Nutanix Enablement Starter Packs (ESPs)?

17. During a six-node cluster deployment, one node fails to image successfully and Foundation is unable to automatically configure the cluster. The consultant decides to manually complete cluster formation with the successful nodes, then expand the cluster with the remaining unconfigured node.

Which command should be used to begin the process?

18. During a technical call with a customer, it is identified that this installation will be software only on Dell servers. The out-of-band management interfaces will not be given IP addresses until the consultant is onsite.

Which Foundation method should be used for this type of installation?

19. A consultant creates a new cluster using ESXi as the hypervisor. After creating the cluster, the consultant begins to run Life Cycle Manager (LCM) updates. During the LCM upgrade pre-checks, an error is returned.

Which configuration is causing this issue?

20. A consultant creates a four-node AHV cluster with two 1GbE (eth0, etc1) and two 10GbE (eth2, eth3) NICs per node. The 1GbE NICs will not be placed into service, but the customer wants the network to be preconfigured for their eventual use.

The consultant removes the 1GbE NIC from the default bond and creates a second bridge(br1), but is unable to add the 1GbE NIC using the below command:

manage_ovs Cbridge_name br1 Cinterfaces 1g Cbond_name br1-up update_uplinks

Which parameter is missing from this command?

21. For a new AHV cluster installation, a customer has 20 NX-8155-G6 nodes with quad port SFP NICs.

The customer wants to meet the following guidelines:

* Take advantage of all available 10GbE links

* Achieve maximum throughput per VM

* Use of redundant ToR switches

* Fastest reconvergence during link failure

How should the load balancing be configured on the host?

22. A consultant creates a Nutanix cluster using the 10.10.10.0/24 network and VLAN 10. The customer creates a VM network inside the Prism using VLAN 20. The customer starts to create VMs but is unable to ping the default gateway from these new systems.

What is causing the issue?

23. Refer to the exhibit.

A consultant is installing AOS 5.10 and ESXi 6.5 on three nodes. During the Foundation process, ESXi 6.5 is not available as one of the choices for hypervisor.

Which solution should the consultant use?

24. While preparing for a new four-node cluster installation, the consultant has a Tech Review Call with the customer.

The hardware is as follows:

* 4 nodes in 1 Block

* 8 x 10 GbE Ports

* 4 x 1 GbE IPMI Ports

* Adequate Ethernet ports are available

* Ethernet cables are correct and available

* Adequate rack space is available

Which remaining item must be confirmed as available onsite?

25. A customer has a G6 AHV cluster with 4x10GbE NICs on each node and the following configuration:

* Networking is set to default

* Only two NICs are connected

The customer receives the following critical message:

The NIC is disconnected from the switch, or the switchport is failing.

What should the consultant verify to resolve the issue?