Network Appliance NS0-506 Free Online Test and PDF Download

1. Which three environmental or physical requirements need to be met when designing a SAN solution? (Choose three.)

2. You have a large, heterogeneous SAN environment. You are asked to gather information for all hosts, HBAs, switches, and storage. You are also told that you must collect this information over network protocols without agents.
Which two NetApp tools allow you to perform this task? (Choose two.)

3. Which information-gathering command should you use to gather logs for troubleshooting switch information for your Brocade switches?

4. You are asked to migrate a SAN LIF to a node that was recently added to your cluster. The following CLI command was provided to you to complete the migration:
network interface modify Cvserver svm1 Clif lif1 Chome Cnode cl01-04 Chomeport 6a
Which step is missing?

5. You are verifying multipathing from the host to the storage controller.
Which three components should you verify? (Choose three.)

6. Click the Exhibit button.


Referring to the exhibit, which entry is appropriate to add to a zone on the FC switch?

7. Click the Exhibit button.
cl01::>igroup show Cvserver
svm1
VserverIgroup Protocol OS
Type Initiators
--------- ------------- ------
-- --------- -----------------
--------------------
svm1 esx_cluster mixed vmware
20:00:00:25:b5:11:a0:01,
20:00:00:25:b5:11:b0:01,
iqn.1998-01.com.vmware:esx02
cl01::>
A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.
What caused the problem?

8. An administrator wants to provide isolation among physical devices connected to the same FCP fabric. Which Cisco switch feature accomplishes this task?

9. You are creating a logical diagram for an FCP SAN solution.
You need to show connectivity between which three sets of components? (Choose three.)

10. When designing a new SAN solution, which three components should be verified with the IMT? (Choose three.)

11. Which two port personality combinations are valid for the onboard UTA2 ports on a FAS8040 controller?

12. Click the Exhibit button.


An administrator is attempting to map an iSCSI LUN to a Windows 2012 host, but the windows host fails to discover the iSCSI targets.
Referring to the exhibit, what is the connectivity problem?

13. Click the Exhibit button.
cl01::>ucadmin show
Current Current Pending
Pending Admin
Node Adapter Mode Type Mode
------------- ------- -------
--------- -------- --------- -
----------
cl01-01 0c fc target - -
online
cl01-01 0d fc target - -
online
cl01-01 3a cna target - -
online
cl01-01 3b cna target - -
online
cl01-01 4a cna target - -
online
cl01-01 4b cna target - -
online
cl02-01 0c fc target - -
online
cl02-01 0d fc target - -
online
cl01-02 3a cna target - -
online
cl01-02 3b cna target - -
online
cl01-02 4a cna target - -
online
cl01-02 4b cna target - -
online
12 entries were displayed.
cl01::>
Referring to the exhibit, which cables are valid for connecting port 0d on node cl01-02 when the switch is 10 meters away?

14. A company has a 4-node Data ONTAP cluster called cl01. The administrator attempts to create a volume on svm1 and can only select aggregates that are owned by node cl01-01 or cl01-02.
What is causing the problem?

15. You created a 5 TB VMware volume “vol_esx_nfs1” in “svm1” for an NFS datastore. The storage efficiency savings of the vmdks are one over 50%, but the application team wants to minimize the possibility of an out-of-space condition. You enable autogrow, autoshrink, and snapshot autodelete with the following commands:
volume modify Cvserver vm1 Cvolume vol_esx_nfs1 Cspace-mgt-try-first volume_grow
snapshotautodelete modify Cvserver vm1 Cvolume vol_esx_nfs1 -enabled true Cdelete-
orderoldest_first Ctarget-free-space 10% -trigger volume
volautosize Cvserver vm1 Cvolume vol_esx_nfs1 Cmode grow_shrink Cmaximum-size 10 TB C
minimum-size 5 TB Cgrow-threshold-percent 80 -shrink-threshold-percent 60
What will these commands do?

16. Which resource would you use to search for information about the configurations for NetApp products that work with third-party solutions?

17. What is a NetApp-recommended zoning best practice?

18. A customer has recently deployed a clustered Data ONTAP 8.3 system and is trying to mount LUNs to a Windows 2012 Server using the iSCSI protocol. They have enabled jumbo frames on their nodes as well as their Windows 2012 Server. Whenever they attempt to scan for a new LUNs, Disk Management times out and does not present any new storage.
What is causing the problem?

19. 75 GB
Used Size: 144 KB
Used Percentage: 5%
Volume Nearly Full Treshold
Percent: 95%
Volume Full Treshold
Percent: 98%
Maximum Autosize (for
flexvolvs only): 6GB
(DEPRECATED) CAutosize
Increment (for flexvolvs
only): 256MB
Minimum Autosize: 5GB
Autosize Grow Threshold
Percentage: 85%
Autosize Shrink Threshold
Percentage: 50%
Autosize Mode: off
Autosize Enabled (for
flexvolvs only): false
Space Guarantee Style: volume
Space Guarantee in Effect:
true
Snapshot Directory Access
Enabled: true
Space Reserved for Snapshot
Copies: 5%
Snapshot Reserve Used: 0%
Snapshot Policy: none
Node name: cl01-01
Reserved Space for
Overwrites: 0B
Fractional Reserve: 100%
Primary Space Management
Strategy: volume_grow
Total Physical Used Size:
144KB
Physical Used Percentage: 0%
A customer has a volume with the configuration shown in the exhibit.
What will happen if the volume vs_iscsi_exch01 reaches 85% used?

20. You have a new FAS8080EX 2-node cluster. The FC switch ports connected to the onboard UTA2 ports will not come online.
Which two node-based issues would case the problem? (Choose two.)