NetApp NCSIE ONTAP Certification NS0-182 Exam Dumps Updated

1. You have set up a new 2-node switchless cluster and want to verify that the failover is configured correctly.

In this scenario, which two commands accomplish this task? (Choose two.)

2. You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.

Which type of SVM needs to be created to complete the installation?

3. Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

4. Which LIF type is used by default for hardware-assisted storage failover communication?

5. You just installed two nodes into an existing ONTAP cluster.

When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.

Referring to the exhibit, which statement is true?

6. When planning the installation of a new ONTAP 9.5 cluster for a customer, which three steps should you perform? (Choose three.)

7. Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it. In this scenario, how would you access Node 4’s management interface?

8. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager. In this scenario, what caused this problem?

9. A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports.

However, LIFs that serve the block have not migrated. In this scenario, what is happening?

10. A customer has a 6-node AFF A700 cluster and wants to add four nodes without having to update license functionality for each node manually. In this scenario, which type of license provides this functionality?

11. In a 4-node cluster, what are two functions of the HA interconnect? (Choose two.)

12. You are cabling two Cisco 3232C switches for the cluster interconnect of a 4-node AFF A800 cluster.

Which pair of ports are used to cable the Inter-Switch Link (ISL) between the switches?

13. After a storage failover, you notice that a NAS LIF, that is linked to the broadcast domain CIFS, is no longer reachable after the takeover. Node cluster1-01 is still waiting for giveback.

Referring to the exhibit, what caused the problem?

14. Which two NetApp features encrypt storage data? (Choose two.)

15. Your customer regularly schedules disaster recovery tests to ensure the high availability capabilities of the ONTAP cluster.

In this scenario, which two commands would you use to perform this test? (Choose two.)

16. Which NetApp tool should you use to set up an ONTAP 9.5 cluster?

17. While preparing for a new ONTAP installation, you discover an issue with the controllers that are running ONTAP 9.5. The issue is not affecting controllers that are running ONTAP 9.4 with the latest patch version. In this scenario, which two steps should you perform to solve the problem? (Choose two.)

18. Which keyboard combination enables you to access the Service Processor (SP) or the Board Management Control (BMC) from the system console CLI?

19. You are installing a new 2-node AFF A220 cluster running ONTAP 9.5. The customer would like to use the UTA2 adapters from the first controller to connect to the 10GbE front-end switches. On the second controller, they would like to use the first UTA2 port as a target FC port, and the second as an FC initiator. In this scenario, according to NetApp Best practices, what should your customer do?

20. You were asked to install a FAS9000 with two quad-port SAS PCI cards. The SAS PCI cards are installed in slot 9 and slot 1. In preparation for the installation, you are filling out the SAS cabling worksheet. In this scenario, which ports are used for the second stack?

21. What are two types of load balancing methods available in multimode interface groups? (Choose two.)

22. You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer’s site, you notice that there are multiple breakout cables and four Cisco 3232C switches. In this scenario, which statement is true?

23. Which statement about LIFs is true?

24. You configured AutoSupport and are trying to send a full AutoSupport message to NetApp.

You use the autosupport history showcommand and see the output shown in the exhibit.

The customer confirms that the AutoSupport settings are correct.

Which two actions will solve this issue? (Choose two.)

25. You are using a NetApp CN1610 cluster-interconnect switch and need to connect a new AFF A800A node to the switch.

In this scenario, how many Ethernet ports per node are required on each switch?

26. You have just installed a new AFF A220 4-node cluster with ONTAP 9.5 for a customer.

Which two cluster switches are supported in this scenario? (Choose two.)

27. You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster.

How many management IP addresses do you need in this scenario?

28. You have a 6-node ONTAP 9.1 cluster with two FAS6290 nodes and four FAS8080 EX nodes using a SAN protocol.

In this scenario, how many FAS9000 HA pairs would be joined to this cluster?

29. After properly cabling the NetApp CN1610 cluster switches, you see that joining the second node to a cluster fails because the node is not able to communicate with the other node.

In this scenario, what is causing this problem?

30. According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?

31. You are planning the deployment of a new 8-node ONTAP 9.5 cluster. To prepare for the installation, you want to create a custom configuration worksheet with all the information that the customer provided. You also want to use the worksheet to generate CLI commands for your installation.

In this scenario, which NetApp tool will help you achieve your goal?

32. You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.

Which two actions should you perform before you turn over the cluster for production? (Choose two.)