Juniper JN0-664 Dumps of DumpsBase (V10.03): Ensure First-Attempt Success and Save Time and Money

1. Which two statements are correct about reflecting inet-vpn unicast prefixes in BGP route reflection? (Choose two.)

2. Exhibit

Click the Exhibit button-Referring to the exhibit, which two statements are correct about BGP routes on R3 that are learned from the ISP-A neighbor? (Choose two.)

3. A packet is received on an interface configured with transmission scheduling. One of the configured queues.

In this scenario, which two actions will be taken by default on a Junos device? (Choose two.)

4. Which two statements are correct about VPLS tunnels? (Choose two.)

5. Exhibit

The network shown in the exhibit is based on IS-IS

Which statement is correct in this scenario?

6. Exhibit

Referring to the exhibit, CE-1 is providing NAT services for the hosts at Site 1 and you must provide Internet access for those hosts

Which two statements are correct in this scenario? (Choose two.)

7. Which three mechanisms are used by Junos platforms to evaluate incoming traffic for CoS purposes? (Choose three )

8. Exhibit

You are asked to exchange routes between R1 and R4 as shown in the exhibit. These two routers use the same AS number.

Which two steps will accomplish this task? (Choose two.)

9. You want to ensure that L1 IS-IS routers have only the most specific routes available from L2 IS-IS routers.

Which action accomplishes this task?

10. Exhibit

CE-1 must advertise ten subnets to PE-1 using BGP Once CE-1 starts advertising the subnets to PE-1, the BGP peering state changes to Active.

Referring to the CLI output shown in the exhibit, which statement is correct?

11. By default, which statement is correct about OSPF summary LSAs?

12. When building an interprovider VPN, you notice on the PE router that you have hidden routes which are received from your BGP peer with family inet labeled-unica3t configured.

Which parameter must you configure to solve this problem?

13. Which two EVPN route types are used to advertise a multihomed Ethernet segment? (Choose two )

14. Exhibit

A network designer would like to create a summary route as shown in the exhibit, but the configuration is not working.

Which three configuration changes will create a summary route? (Choose three.)

15. An interface is configured with a behavior aggregate classifier and a multifield classifier How will the packet be processed when received on this interface?

16. Exhibit

A network is using IS-IS for routing.

In this scenario, why are there two TLVs shown in the exhibit?

17. In IS-IS, which two statements are correct about the designated intermediate system (DIS) on a multi-access network segment? (Choose two)

18. Exhibit

You are attempting to summarize routes from the 203.0.113.128/25 IP block on R8 to AS 64500. You implement the export policy shown in the exhibit and all routes from the routing table stop being advertised.

In this scenario, which two steps would you take to summarize the route in BGP? (Choose two.)

19. Exhibit

You must ensure that the VPN backbone is preferred over the back door intra-area link as long as the VPN is available. Referring to the exhibit, which action will accomplish this task?

20. Exhibit

Which two statements about the output shown in the exhibit are correct? (Choose two.)

21. Which two statements are correct regarding bootstrap messages that are forwarded within a PIM sparse mode domain? (Choose two.)

22. Exhibit

R1 and R8 are not receiving each other's routes

Referring to the exhibit, what are three configuration commands that would solve this problem? (Choose three.)

23. Which statement is true regarding BGP FlowSpec?

24. Exhibit

You have MAC addresses moving in your EVPN environment

Referring to the exhibit, which two statements are correct about the sequence number? (Choose two)

25. You are responding to an RFP for a new MPLS VPN implementation. The solution must use LDP for signaling and support Layer 2 connectivity without using BGP. The solution must be scalable and support multiple VPN connections over a single MPLS LSP The customer wants to maintain all routing for their Private network

In this scenario, which solution do you propose?