HP FlexNetwork Solutions V3 HP0-Y52 Dumps Questions

1. An HP Comware switch should send messages to an SNMP server when various events occur.

What is one step in the configuration of this feature?

2. Exhibit1.

Exhibit 2

A network administrator wants to create a backup IP route to 10.1.20.0/24 on Switch-1. The backup route should use Link 2, and it should only be used if Link 1 is down.

What is the correct setup to accomplish this?

3. Refer to the exhibit.

This switch currently assigns all VLANs to Multiple Spanning Tree Protocol (MSTP) instance 0 or the Internal Spanning Tree (IST).

Which statement correctly describes interface 21?

4. Refer to the Exhibit.

Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2.

How does this affect the Multiple Spanning Tree Protocol (MSTP) topology?

5. Refer to the Exhibit.

A network administrator has configured an HP Comware switch to act as the DHCP server for VLAN 12, but the switch is not responding to clients’ DHCPDISCOVER messages.

Based on the exhibit, what is the problem with the DHCP configuration?

6. Refer to the Exhibit.

Examine the output from the Comware command shown in the exhibit.

Based on the flag of ACDEF, what is the status of the aggregated link?

7. A network administrator enters this command on an HP Comware switch:

<Comware> save

In interactive mode, the administrator is prompted to save to a file named config.cfg and confirms the save.

What is the effect of these actions?

8. A customer is implementing a network using HP ProVision switches.

Which default setting applies to the ProVision switches?

9. A company needs a two-member Intelligent Resilient Framework (IRF) virtual switch. The network administrator is configuring IRF member 2 that will connect to port 1/1 on IRF member 1.

What is the correct IRF port ID for member 2?

10. A customer wants to implement multiple links between a server and a single HP Comware switch in order to increase the amount of bandwidth for more throughput.

Which feature should the network administrator implement to accomplish this?

11. A network administrator configures this command on an HP ProVision switch:

vlan 30 ip helper-address 10.0.3.253

The switch is able to ping 10.0.3.253. After the administrator configures the command, users in VLAN 30 report that their PCs fall to acquire addresses using DHCP.

What should the administrator ensure?

12. What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?

13. Refer to the exhibit.

The exhibit shows partial output of the HP Comware display ip routing-table command. Note the Pre or preference column.

On an HP ProVision switch, what is the corresponding term used for the Pre column in the Comware output shown in the exhibit?

14. A server connects to a port on an HP Comware switch.

The network administrator wants to ensure that:

- the port remains forwarding during Multiple Spanning Tree Protocol (MSTP) topology changes, and

- changes in the port status do not cause MSTP topology changes.

Which statement describes how the administrator can accomplish this?

15. Refer to the exhibit.

The network administrator has configured this port to permit all VLANs. The output in the exhibit indicates that the port is only passing VLANs 1 and 11. The administrator wants the port to pass VLAN 12 as well.

What should the administrator do to accomplish this?

16. Refer to the exhibits.

Exhibit 1

Exhibit 2

All of the switches in Exhibit 1 are routing switches. Exhibit 2 shows the routes configured on these switches. The direct (connected) routes are not shown, but assume that links are configured with the IP addresses shown in Exhibit 1.

The network administrator wants to protect communications between clients and servers in case Link 1 fails.

What should the administrator do to protect these communications in this failover situation?

17. Refer to the exhibit.

The switches in the exhibit are all HP Comware switches that run Multiple Spanning Tree Protocol (MSTP).

The network administrator wants to ensure that each switch-to-switch link is in its own subnet. The administrator also wants to make sure that all of the links are available for routing during normal operation.

How should the administrator configure the physical switch-to-switch interfaces to accomplish these goals?

18. Refer to the exhibit.

Assume that Student A’s ARP table is empty. Student A is preparing to send an FTP packet to FTP Server B and needs to discover the proper destination MAC address.

For which IP address does Student A send an ARP request?

19. Which HP software platform provides centralized network management, monitoring, and configuration of wired and wireless network infrastructure devices, as well as traffic monitoring, user management, and other capabilities?

20. Which statement is true about wireless technologies?

21. A network administrator enters this command on an HP ProVision switch with IP routing enabled:

ip route 0.0.0.0/0 10.1.1.1 metric 10 distance 10

This is the only IP route to 0.0.0.0/0 on the switch.

What is the effect?

22. HOTSPOT

Match the description with the 802.11 standard. (Each option may be used only once.)

23. A network administrator is managing an HP Comware switch from the CLI.

Which action can the administrator only perform in User view?

24. Refer to the exhibit.

A network administrator enters the command shown in the exhibit to check the VLANs on an HP ProVision switch interface. The administrator wants to discover which VLANs are tagged and untagged on the port.

What can the administrator do to accomplish this?

25. Which HP device or port type can modify, read, and respond with frames that include 802.1Q VLAN tags?

26. Refer to the exhibit.

A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to the flash of the switch, the process fails because there is not enough flash to store the new operating system. The new operating system is 3.2MB in size. The administrator then executes the commands shown in the exhibit above.

Which action should the administrator perform to solve this problem?

27. A company wants a modular switch for the access layer at its main campus and for several branch offices.

Which HP Switch Series is best suited for this role?

28. Which methods can a network administrator use to upgrade the operating system of an HP ProVision switch? (Select two.)

29. Refer to the exhibit.

The topology shown in this exhibit implements Multiple Spanning Tree Protocol (MSTP), where all the switches are in the same region.

How many MSTP instances, besides the Internal Spanning Tree (IST) or instance 0, does this network need in order to have effective load sharing on the uplinks from the access switches?

30. Which command can a network administrator execute on an HP Comware switch to manage configuration files?

31. Refer to the exhibit.

Which endpoint or endpoints receive broadcast ARP requests sent by EndpointA?

32. Refer to the exhibits.

Exhibit 1

Exhibit 2

PC1 cannot reach PC2. Based on the exhibits, what could be causing this error?

33. What does the traceroute command identify on an HP ProVision switch?

34. An HP ProVision switch is operating at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection is carrying untagged traffic. The administrator wants to log in to the switch CLI using Telnet.

How should the administrator contact the switch and log in?

35. Which statement correctly defines the management capabilities of an HP MultiService Mobility (MSM) access point (AP)?

36. Two switches are members in an active Intelligent Resilient Framework (IRF) virtual device. A network administrator joins a third switch to the IRF virtual device.

Which switch is now the master?

37. Refer to the exhibit.

The network administrator is setting up Multiple Spanning Tree Protocol (MSTP) with the settings shown in the exhibit. All the switches are in the same region. The administrator has requested help determining which VLANs each switch-to-switch link should carry.

What is a recommendation for this topology?

38. Refer to the exhibit.

A network administrator has implemented link aggregation on an HP Comware switch using LACP. The two ports are functioning at the data link layer between the Comware switch and its neighboring switch. The administrator executes the display link-aggregation verbose command and notices the flags shown in the exhibit.

What does this indicate?

39. Refer to the exhibit.

An HP Comware switch is using its default user-interface settings. The network administrator then enters the commands shown in the exhibit.

What correctly describes how an admin user must now log in?

40. Which term refers to aggregated links on HP ProVision switches?

41. Which credential is required to validate SNMPv2c write requests?

42. A customer is implementing an access layer solution with four HP Comware switches in an Intelligent Resilient Framework (IRF) virtual device or domain. The customer expects to add two additional switches of the same model and would like to add them to the existing IRF virtual device.

What must the customer verify?

43. A tagged frame arrives on a switch port that is not a tagged member of the VLAN indicated by the frame ID.

What do fundamental VLAN operating rules require the switch to do with that frame?

44. A network administrator wants to disable physical interfaces 13-24 on an HP ProVision switch.

How can the administrator do this?

45. Refer to Exhibit.

The server shown in the exhibit requires redundant links, and The link aggregation should use LACP.

What should the administrator configure on the 1RF virtual switch?