Dell PowerEdge MX Modular Deploy 2023 Certification Exam: Real D-PEMX-DY-23 Exam Dumps for Learning

For those seeking to pass the D-PEMX-DY-23 Dell PowerEdge MX Modular Deploy 2023 certification exam, the real D-PEMX-DY-23 exam dumps offered by DumpsBase can be a significant exam resource. The D-PEMX-DY-23 exam dumps of DumpsBase are an excellent resource for efficient Dell PowerEdge MX Modular Deploy 2023 exam preparation. These dumps containing 135 questions and answers allow candidates to verify their preparation level and stay updated with the latest exam trends. Moreover, they are ideal for those with no prior experience in taking the Dell PowerEdge MX Modular Deploy 2023 certification exam. The D-PEMX-DY-23 dumps are designed to be accessible on both PCs and mobile phones, allowing candidates to study anywhere, anytime. The real D-PEMX-DY-23 exam dumps facilitate easy exam preparation and ensure candidates are well-prepared to pass the Dell PowerEdge MX Modular Deploy 2023 exam on the first attempt.

Dell PowerEdge MX Modular Deploy 2023 Certification Exam D-PEMX-DY-23 Free Dumps

1. What is a valid option when resetting iDRAC to factory defaults?

2. Which ports will be active in an MX9116n FSE if there are dual-port NICs in all the server sleds?

3. What type of connection is used by QuickSync 2?

4. A network administrator must implement a 100 GbE network in their MX7000 chassis group.

Which two components satisfy this requirement?

(Select 2)

5. Why is the backup lead configuration important in an MCM Group?

6. Which I/O module is supported for Fabric B?

7. What configuration is supported for a fully populated MX740c compute sled?

8. Which protocol(s) does Redfish use?

9. A systems administrator must extract log files from an MX7000. The logs cannot be saved locally and must only be stored on a secure file server.

Which share protocols can they use to save the logs?

10. A customer is implementing a clustered three-chassis solution.

Which two components are required?

(Select 2)

11. What is the number of server-facing ports and the bandwidth of each port on the MXG610s?

(Choose two.)

12. What does OBPAR allow on a PowerEdge MX750c?

13. An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up. Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?

14. Which three components are required in an MX7000 chassis to allow multiple compute sleds to share access to the same disks in an MX5016s enclosure?

(Select 3)

15. The MX9116n FSE has two single-density QSFP28 port groups, and the default setting for these two ports is 1x 100GbE.

What other Ethernet breakout configurations are supported?

16. Which two-socket PowerEdge sled can support up to eight E3.s NVMe Gen 5 SSD drives?

17. Which is an invalid option for the PowerEdge MX7000 control panel?

18. What is a characteristic of MX7000 networking in Scalable Fabric Mode?

19. Which VLAN is reserved for internal switch communication?

20. A data center team is working on a solution to monitor and manage data center devices from anywhere.

Which feature can be configured to perform these tasks?

21. When multiple MX9002m modules are daisy-chained to Top-of-Rack switches, which uplink port can be used for stacking?

22. What are two considerations when adding an MX760c in a chassis running OME-M firmware earlier than v2.0?

(Select 2)

23. Which is a logical resource in SmartFabric?

24. What type of video connector is available for KVM connectivity on the PowerEdge MX7000 chassis?

25. An implementation engineer prepares to install a PowerEdge MX7000.

Which serial cable do they use?

26. What feature does OME-M v1.3 provide when replacing the Right Control Panel?

27. A server administrator wants to configure RAID on drives that are assigned to a compute sled.

Which interface can be used to complete the task?

28. What are the correct CLI commands to configure the management IP Address on either the MX9116n or the MX5108n switches running SmartFabric OS10?

29. A system administrator must assign six of the MX5016s drives to a single MX750c compute node.

Which assignment mode accomplishes this task?

30. What are the components of the control panel of a PowerEdge MX750c sled?

31. Which feature in OpenManage Mobile can be used to allow the monitoring of a PowerEdge MX7000 chassis?

32. An administrator is receiving notifications about insufficient power for a PowerEdge MX7000 chassis. The chassis is fed from two different power grids.

What is the best policy to maximize power and maintain uptime?

33. Which micro controller-based module allows the Management Module to communicate with all the hardware present in a PowerEdge MX7000 chassis?

34. An administrator is asked to install and power-on a new MX740c sled in an MX7000 chassis. The administrator inserts the sled and presses the power button. They notice that the power button LED is blinking green. After a short time power button turns to solid green and the server finally turns on.

What operation was in progress when the power button was blinking green?

35. What is the maximum number of mezzanine cards that can be installed in an MX840c?

36. A PowerEdge MX7000 administrator is tasked to perform a chassis update using a catalog.

Which source options are used to create the catalog?

37. What is a function of the Fabric Resources Director (FReD)?

38. An administrator is sending servers to other individuals but wants to reset the server to the factory default first.

What LifeCycle Controller feature is used to complete this action?

39. What is the connection protocol between FReD and MM?

40. Which two actions are possible using the Chassis Deployment Wizard?

(Select 2)

41. A customer wants to change the switch operating mode from SmartFabric mode to Full Switch mode. After deleting the fabric in OME-M, what configuration is retained on the switch?

42. What is the minimum OME-M version required to use ATMOS?

43. Which command(s) is supported in the current PowerEdge MX Redfish implementation?

44. After a main board replacement, the easy restore process was not successful. A system administrator is not able to launch the Virtual Console.

What is the cause of this issue?

45. A customer would like to periodically change the iDRAC root password on all the servers in their MCM Group.

What feature in OME-M should they use?

46. What is the port configuration of an MX5108n switch?

47. What item is used to refer to a daisy-chained configuration of a multiple MX7000 chassis environment?

48. What are two requirements to achieve 100 GbE network speeds for a compute sled?

(Select 2)

49. What location allows an administrator to enable DHCP for every iDRAC in the MX7000?

50. Which feature requires an iDRAC Enterprise license for a compute sled on a PowerEdge MX7000 chassis?


 

Get Ready to Pass the D-RP-OE-A-24 Exam - Buy the D-RP-OE-A-24 Dumps to Prepare for Your Dell RecoverPoint Operate Exam
Becoming a DELL EMC Certified Professional: Real D-PM-IN-23 Dumps for Passing Dell PowerMax Install 2023 Exam

Add a Comment

Your email address will not be published. Required fields are marked *