Dell Networking Associate Exam DCAN-100 Dumps Questions Online

1. Refer to the output:
console#show interfaces switchport te1/0/1
Port: Te1/0/1
VLAN Membership Mode: General Mode
Access Mode VLAN: 1 (default)
General Mode PVID: 9
General Mode Ingress Filtering: Enabled
General Mode Acceptable Frame Type: Admit All
General Mode Dynamically Added VLANs:
General Mode Untagged VLANs: 1, 9
General Mode Tagged VLANs: 10-11
General Mode Forbidden VLANs:
Trunking Mode Native VLAN: 1 (default)
Trunking Mode Native VLAN Tagging: Disabled
Trunking Mode VLANs Enabled: All
Private VLAN Host Association: none
Private VLAN Mapping:
Private VLAN Operational Bindings:
Default Priority: 0
Protected: Disabled
console#
What VLAN will untagged ingress traffic be assigned?

2. Refer to the output:
spanning-tree mode mst
spanning-tree mode mst configuration
revision 1
instance 1 add vlan 2-4
instance 2 add vlan 5-10
exit
A technician needs to add a new switch to an existing MST network. The new switch is NOT able to join the current MST domain.
Which action will allow the switch to join the current MST domain?

3. A technician enables Dot1x RADIUS authentication globally on all ports on the N2000 switch. All ports show as unauthorized and management access to the switch has been lost.
What is causing network connectivity loss on the switch?

4. A technician creates a new connection between two switches. After configuring the VLANs, the technician looks at the MAC table and sees no MAC addresses learned on the new interface. When looking at “show spanning-tree”, the technician sees the port mode is “Alt.”
What is causing this behavior?

5. Refer to the output:
console#show interfaces switchport gigabitethernet 1/0/5
Port: Gi1/0/5
VLAN Membership Mode: Access Mode
Access Mode VLAN: 3
General Mode PVID: 1 (default)
General Mode Ingress Filtering: Enabled
General Mode Acceptable Frame Type: Admit All
General Mode Dynamically Added VLANs:
General Mode Untagged VLANs: 1
General Mode Tagged VLANs:
General Mode Forbidden VLANs:
Trunking Mode Native VLAN: 1 (default)
Trunking Mode Native VLAN Tagging: Disabled
Trunking Mode VLANs Enabled: All
Private VLAN Host Association: none
Private VLAN Mapping:
Private VLAN Operational Bindings:
Default Priority: 0
Protected: Disabled
Port Gi1/0/5 on a Dell N2024 will be used to create an IEEE 802.1Q-compliant trunk to another switch.
Why will the trunk fail to form?

6. A technician implements a new copper connection to Gi2/0/20.
Which command should be used to check the cable length?

7. Refer to the output shown:


Which two statements describe the state of configuration of interfaces gi1/0/1-24? (Choose two.)

8. Refer to the output.


A technician implements a new N-Series switch and connects it to another N-Series switch with OSPF already configured. The OSPF neighbor does not show up after 5 minutes of waiting.
What is causing the issue?

9. A Dell Networking N-Series switch is directly connected to a wireless Access Point that requires access to VLANs 1, 10, and 20 configured on the switch.
Which two Port VLAN Modes can be used to meet the VLAN requirements? (Choose two.)

10. A client must connect a printer located on a public area on an X1000. The client is concerned someone will use the printer Ethernet cable to gain unauthorized network access.
Which configuration will help prevent unauthorized accesses?

11. A technician decides to create an ACL. The technician includes all host and/or protocols allowed within the ACL.
Why must the technician take this step?

12. A client needs to allow Telnet traffic from the 192.168.1.0/25 network. The client needs to configure the “permit” statement in the ACL.
Which command will accomplish this goal?

13. Which three services use UDP for data segment transportation? (Choose three.)

14. A technician wants to allow SSH connections to authenticate using an external server. If the external server becomes unreachable, the users created on the switch should be allowed.
What command will accomplish this goal?

15. Refer to the output:


A network outage occurs. A technician tries to log in to a switch by Telnet using the correct local username and password.
What is causing the login failure?

16. Which command shows active telnet sessions on Dell N-Series switches?

17. Refer to the output.


Which two actions occur if interface Tw2/0/2 goes down? (Choose two.)

18. A technician is using Telnet to access an N2024P. Connections are being terminated after 10 minutes of inactivity.
Which action should the technician perform to extend the amount of allowed inactivity time

19. A technician has one stack of three N3024. The technician removes the master unit without powering off the stack. This unit is reconfigured with new IP address in the same Layer 2 network.

Which management issue is the result?

20. A technician applies an IPv4 address to the Out-Of-Band/Management port of a Dell N-Series switch.
Which step allows the technician to use the web interface?