Choose Authentic 300-610 Dumps (V19.03) of DumpsBase to Make Preparations – Start Reading 300-610 Free Dumps (Part 2, Q41-Q90)

1. A network engineer is using a Cisco UCS environment connected to a Fibre Channel storage array. The Cisco UCS environment must be connected to an existing SAN network, and several Cisco MDS 9000 Series Switches must be added to increase storage density.

The solution must not exhaust the SAN network from the list of available domain IDs after connecting Also, most of the SAN traffic must be mapped from the Cisco UCS blades to a specific group of the fabric interconnect ports.

Which two features must be deployed to meet these requirements? (Choose

two.)

2. An engineer is implementing a storage area network where an NPV is used. The engineer notices that the servers in a storage farm are experiencing heavy traffic contention. The engineer needs to migrate traffic from heavily loaded server interfaces to interfaces with less load. When the new links are deployed, the existing traffic is not rebalanced as expected.

Which feature must be used to meet these requirements?

3. When planning to deploy a load-balancing service as a managed node, which ACI configuration must be included?

4. An engineer must logically partition two Cisco Nexus 7000 Series Switches into two environments called Test_39919596 and Production_59423879. The environments must use only F2-Series line cards and be limited to a maximum of 265 port-channels.

Which Cisco Nexus feature must be used?

5. An ACI deployment must:

- Only use a proxy for border leaf switches.

- Classily incoming traffic on L3OUT.

- Immediately update the endpoint database when the endpoint moves between loaf switches.

Which VRF configuration must be used?

6. Which address pool is used when a vHBA template is created?

7. Place a firewall between the VDCs.

D. 1) Create a separate VRF for the testing and development environments.

2) Control reachability by using firewall access policies.

8. An engineer must deploy a Cisco HyperFlex system at two data centers. For redundancy reasons, the setup must achieve data protection in case of an entire site failure. The data must be available on both sites at all times to keep the recovery time objective to a minimum.

Which Cisco HyperFlex deployment model meets these requirements?

9. An engineer must design a VXLAN EVPN network. The solution should optimize broadcast, unknown unicast, and multicast (BUM) and short BUM replication, and use PIM anycast RP.

Which solution should be included in the design?

10. A Cisco engineer is preparing a service profile template for a design, which consists of 20 x UCS B200M6 blade servers 2 x UCS 6454 Fabric Interconnect in End Host Mode, and 3 x UCS 5108 server chassis with 2408 Fabric Extenders The blade servers are equipped with VIC 1480 adapters The engineer does not configure a vNIC/vHBA placement policy in the service profile and the vNICs and vHBAs are assigned to the vCon in a particular order What is the mapping scheme in which Cisco UCS assigns the vCons based on the type of server and the selected virtual slot?

11. What can be implemented on Cisco Nexus 5600 Series Switches for link redundancy within

a Fibre Channel fabric?

12. An engineer is configuring a Cisco UCS Service Profile template for an environment that will host Windows servers Some of the servers require access to a Fibre Channel storage network The design requires the server HBA to send the maximum number of commands to a Fibre Channel disk using a single transmission.

Which action must be taken to meet these requirements?

13. An engineer needs to configure multiple network devices using Ansible Device passwords must meet these requirements:

✑ be stored securely

✑ not be visible as plaintext

✑ be available to Ansible playbooks for executing scripts.

Which solution must the engineer choose?

14. An engineer must design a DNS service available to multiple network zones as a shared service. The network zones are deployed as VRFs within the data center network and no firewall is available for communication between VRFs.

Which protocol is needed to implement the shared services?

15. An engineer must connect an existing Cisco Fabric Interconnect to an IP-based storage array. The connection be a channel made directly between the fabric interconnect expansion module and the storage array. The engineer must also consider that the environment is running FCoE for storage and uses QoS to prioritize traffic.

Which port type should be used to meet these requirements?

16. A customer requires a tool to manage Cisco network hardware. The solution must use secure communication using a secure network protocol, support the use of declarative language to manage the state of resources, and periodically pull changes to the controlled nodes.

Which tool meets these requirements?

17. A Cisco engineer is configuring MPLS VPN BGP at a customer site that is connected to the provider site by more than one path MPLS VPN BGP Local Convergence link protection is enabled. After the engineer installs the main forwarding path and the redundant backup path within the BGP, they assign a unique route distinguisher to each VRF table on all PE devices that serve as a backup to the link.

What is a prerequisite for this local convergence to work?

18. Which two methods mitigate congestion in a SAN network? (Choose two.)

19. Refer to the exhibit.

Server 1 fails to connect to the storage array over the Storage Area Network (SAN) of the Cisco NDS 9000 Series Switch.

The requirements are to redesign the storage network and keep these considerations in mind:

✑ The traffic from each of the server must be redundant and isolated.

✑ The design must tolerate hardware and software failures and upgrades of SAN fabric devices.

Which action must be taken to meet these requirements?

20. An engineer must design a multitenant solution using Cisco 7709 switches. The solution must support separate routing instances, separate spanning tree domains, and separate firewalls for each tenant.

Which solution meets these requirements?

21. A network consultant evaluates the Cisco UCS Fabric Interconnect SAN configuration, which must meet these requirements:

✑ All traffic must pass over the upstream device for switching and domain IDs must be preserved in the fabric.

✑ Each server should be pinned to one designated upstream interface and for the traffic to pass through the pinned port.

Which Fabric Interconnect SAN operational mode meets these requirements?

22. What are two functions of a Network Services Orchestrator in an NFV environment? (Choose two.)

23. Refer to the exhibit.

An engineer is configuring a QoS policy with these requirements

✑ Match-all AF11 traffic and set it to a DSCP value of 14.

✑ The committed rate must be 10 Mbps with a committed burst rate of 1000 ms

✑ Drop any AF11 traffic that violates these settings.

✑ Any traffic other than af11 must have a DSCP value of 0

The given class-map configuration already exists.

Which solution must the engineer use to meet the requirements?

A)

B)

C)

D)

24. Refer to the exhibit.

In this scenario a Cisco engineer is building a loop-free topology where a dedicated layer of the vPC domain adjacent to the aggregation layer which also runs vPC Is used to interconnect the two data centers together. The engineer globally configures a vPC domain identifier on both vPC devices where the domain ID is the same on both peer devices.

Which action successfully forms the domain?

25. A network consultant must design a high availability interconnection of a clustered Cisco UCS Fabric Interconnect toward two upstream Layer 2 switches. The Ethernet interconnection must use all redundant links and have no impact on the STP domain size.

Which connectivity solution must be used?

26. What is an advantage of Cisco HyperFlex Edge as compared to Cisco HyperFlex Standard Clusters?

27. An engineer must implement an iSCSI storage connectivity in the existing Cisco UCS environment. The environment is based on Cisco UCS -Series rack server, Cisco Nexus 1000V Series Switches, and VMware ESXi hosts.

The implementation must meet these requirements:

✑ Provide multipathing and high availability in the event of a critical path failure.

✑ Be cost-effective and not require the purchase of new equipment.

Which two components must be selected to meet these requirements? (Choose two.)

28. An engineer must connect a storage array directly to an existing Cisco UCS Fabric Interconnect. The customer requires a solution that provides IP-based storage that does not need to be connected through an external switch Also, the operations team wants to have the ability to have direct access to the files stored on the storage array from their Linux hosts.

Which storage technology meets these requirements?

29. An architect must automate routine tasks within a data center The data center exclusively uses Cisco Nexus Series Switches The networking team lacks proper programming knowledge and prefers an automation solution that leverages NXOS commands Any configuration change must use HTTPS for transport due to a security compliance requirement.

Which solution must the architect choose?

30. Which two statements describe Ethernet switching mode on Cisco UCS 6100 Series Fabric Interconnects? (Choose two.)

31. Which orchestration tool should be used for the management and analytics of servers across multiple sites?

32. A company must integrate an iSCSI storage solution into its existing production environment. The new iSCSI network must be accessible from a limited set of network segments. The client devices follow a strict network security policy to access critical data from the storage array.

Which design steps must be used to meet these requirements?

33. A network consultant proposes that the configuration of the Cisco UCS servers be based on service templates to facilitate the UCS infrastructure operation. The service profiles must remain connected to the template and be modified when the template settings are changed.

Which configuration meets these requirements?

34. An engineer requires a solution that achieves Ethernet traffic forwarding on all available paths from the hosts to the Cisco Nexus Fabric Extender and from the Fabric Extenders to the Cisco Nexus 5000 Series Switches. The NIC teaming from the Fabric Extender to a server should use an LACP EtherChannel.

Which solution should be implemented to meet these requirements?

35. A network architect designs a high-availability architecture for the Cisco UCS Fabric interconnects that installed in a data center. The architecture must support clustering and redundancy.

Which architecture meets these requirements?

36. Refer to the exhibit.

The Cisco Nexus Series Switch with hostname Nexus! is the default gateway for server A and server B Both servers must have reachability to the internet; however, server A internet traffic must pass through the firewall for deep packet inspection. Also, the firewall must inspect any communication between server A and server B.

Which solution must be applied to separate the data plane path for server A and server B?

37. Refer to the exhibit.

A system administrator needs a solution to manage random packet drops between two Cisco UCS C240 M4 servers The servers are connected to a pair of Cisco Nexus 7009 switches using 10G fibre interfaces Both servers are generating too many east-west traffic flows from TCP-based applications which causes significant latency that impacts the customer Also the transfer of files from Server-1 to Server-2 larger than 10 GB results in multiple retransmits.

Which design solution resolves this issue?

38. A storage administrator receives reports of network delays when database software attempts to access the storage array. The virtual machines that host the database software are installed on different rack servers connected to the Cisco UCS Fabric Interconnect domain. The existing SAN switches are connected to the Fabric Interconnects using two 8 Gb port-channel interfaces to connect the storage array. The storage administrator has decided to deploy iSCSI storage with four 10 Gbps interfaces connected to the Cisco UCS Fabric Interconnects.

Which deployment type resolves the problems with storage contention?

39. A network architect designs the iSCSI-based storage area network solution. The iSCSI datastore must be designed with high availability, minimal downtime, and no single point of failure. The requirement is to fail over I/O to alternate paths based on SCSI sense codes without reliance on network failures.

Which feature must be deployed to meet these requirements?

40. An engineer is designing a Cisco 7000 Series disaster recovery site using the data center interconnect solution to provide gateway redundancy and needs to ensure that devices use gateways in their own data centers.

Which design approach should be used to accomplish this goal?

41. An engineer must configure a new maintenance policy that will apply to multiple Cisco UCS domains. The policy must be available for use by service profiles and service profile templates created and managed n either Cisco UCS Manager or Cisco UCS Central Changes to this policy must be allowed only in Cisco UCS Central.

Which policy type must the engineer select to accomplish these goals?

42. Refer to the exhibit.

A cloud provider service provider deployed three geographically separated Cisco ACI data centers. One of the customers needs to host a clustered application that is spread across the three data centers. The cluster nodes that host the application need a layer 2 topology to communicate with each other.

Which Cisco ACI topology design meets these requirements?

43. An engineer must design a Cisco HyperFlex solution to support a virtualized environment in a single data center location.

The design must consider these customer requirements:

✑ a large-scale cluster with eight or more nodes

✑ distributed high-performance file system for virtualized servers

✑ high fault tolerance to multiple node failures

Which action meets these objectives?

44. A company has several data centers with hundreds of Cisco UCS blade chassis. A network consultant plans to active Cisco Discovery Protocol to the servers to facilitate Layer 1 troubleshooting. For security reasons, the company wants to restrict the servers from sending different MAC addresses to the fabric interconnect after the MAC address from the first packet is learned.

Which two policies be modified to support this design? (Choose two.)

45. Refer to the exhibit

Due to power limitations at the customer data center, the engineering team must decommission one of the modular switches In the new design the customer must ensure that the OSPF process is fully protected on the remaining switch and minimize OSPF flapping in case of any module failure.

Which solution fulfills the requirements for the new design?

46. Refer to the exhibit.

The FCoE packets fail to be forwarded through the switch.

What is the minimum MTU QoS requirement for the FCoE to work?

47. A network consultant evaluates the Ethernet Adapter Policy configuration to be applied to the Cisco UCS blade servers. The policy must minimize latency and increase throughput for sensitive applications. The solution must increase the CPU data cache hit rate to meet these requirements.

Which policy is required?

48. Refer to the exhibit.

A Cisco UCS chassis that has two IOMs is discovered. The chassis discovery policy creates a fabric port channel.

What is the result of this policy?

49. An engineer is expanding an existing ISCSI environment and must choose an addressing scheme. When checking one of the devices, the engineer discovers this target device naming used {prefix}. 2019-01.com.acme.123:00. ftd0cb21.bcb389458389

Which addressing scheme was used in the environment?

50. The data center aggregation layer that uses IPv4 and IPv6 address space must act as a redundant Layer 3 gateway. The solution must support a minimum of 240 virtual groups for an interface The data center aggregation layer hosts network devices from different vendors.

Which FHRP solution meets these requirements?