2V0-41.24 Exam Dumps (V9.02) – Ensuring that You Are Equipped with the Knowledge and Skills Needed to Secure a Successful Career

1. What is the VMware recommended way to deploy a virtual NSX Edge Node?

2. Which three selections are capabilities of Network Topology? (Choose three.)

3. An NSX administrator has deployed a single NSX Manager node and will be adding two additional nodes to form a 3-node NSX Management Cluster for a production environment. The administrator will deploy these two additional nodes and Cluster VIP using the NSX UI.

What two are the prerequisites for this configuration? (Choose two.)

4. Which two commands does an NSX administrator use to check the IP address of the VMkernel port for the Geneve protocol on the ESXi transport node? (Choose two.)

5. Which two are supported by L2 VPN clients? (Choose two.)

6. As part of an organization’s IT security compliance requirement, NSX Manager must be configured for 2FA (two-factor authentication).

What should an NSX administrator have ready before the integration can be configured?

7. What should an NSX administrator check to verify that VMware Identity Manager integration is successful?

8. An administrator has been tasked with implementing the SSL certificates for the NSX Manager Cluster VIP.

Which is the correct way to implement this change?

9. An administrator wants to validate the BGP connection status between the Tier-0 Gateway and the upstream physical router.

What sequence of commands could be used to check this status on NSX Edge node?

10. What is VMware’s recommendation for the minimum MTU requirements when planning an NSX deployment?

11. In which VPN type are the Virtual Tunnel interfaces (VTI) used?

12. In an NSX environment, an administrator is observing low throughput and congestion between the Tier-0 Gateway and the upstream physical routers.

Which two actions could address low throughput and congestion? (Choose two.)

13. A company security policy requires all users to log into applications using a centralized authentication system.

Which two authentication, authorization, and accounting (AAA) systems are available when integrating NSX with VMware Identity Manager? (Choose two.)

14. An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events.

Which message ID (msgid) should be used in the syslog export configuration command as a filter?

15. An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing.

Which failover detection protocol must be used to meet this requirement?

16. An administrator has connected two virtual machines on the same overlay segment. Ping between both virtual machines is successful.

What type of network boundary does this represent?

17. What are two supported host switch modes? (Choose two.)

18. Which is an advantage of an L2 VPN in an NSX 4.x environment?

19. Which two steps must an NSX administrator take to integrate VMware Identity Manager in NSX to support role-based access control? (Choose two.)

20. Which of the two following characteristics about NAT64 are true? (Choose two.)

21. Which VMware GUI tool is used to identify problems in a physical network?

22. Which three protocols could an NSX administrator use to transfer log messages to a remote log server? (Choose three.)

23. Where does an administrator configure the VLANs used in VRF Lite? (Choose two.)

24. Which two logical router components span across all transport nodes? (Choose two.)

25. What must be configured on Transport Nodes for encapsulation and decapsulation of Geneve protocol?

26. A customer is preparing to deploy a VMware Kubernetes solution in an NSX environment.

What is the minimum MTU size for the UPLINK profile?

27. What are three NSX Manager roles? (Choose three.)

28. Which two CLI commands could be used to see if vmnic link status is down? (Choose two.)

29. Which VMware NSX Portfolio product can be described as a distributed analysis solution that provides visibility and dynamic security policy enforcement for NSX environments?

30. An administrator has a requirement to have consistent policy configuration and enforcement across NSX instances.

What feature of NSX fulfills this requirement?

31. When collecting support bundles through NSX Manager, which files should be excluded for potentially containing sensitive information?

32. What can the administrator use to identify overlay segments in an NSX environment if troubleshooting is required?

33. How does the Traceflow tool identify issues in a network?

34. Where is the insertion point for East-West network introspection?

35. Which is the only supported mode in NSX Global Manager when using Federation?

36. When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?

37. An NSX administrator is creating a Tier-1 Gateway configured in Active-Standby High Availability

Mode. In the event of node failure, the failover policy should not allow the original failed node to

become the Active node upon recovery.

Which failover policy meets this requirement?

38. Which CLI command is used for packet capture on the ESXi Node?

39. Which command on ESXi is used to verify the Local Control Plane connectivity with Central Control Plane?

40. Which two statements describe the characteristics of an Edge Cluster in NSX? (Choose two.)