300-610 Dumps Updated to V19.03 – Choose the Latest Dumps by Reading 300-610 Free Dumps (Part 1, Q1-Q40) First

1. An end user is experiencing network latency when accessing a database in a disaster recovery site. The monitoring team concluded that the database was writing simultaneously to the storage arrays on the primary and disaster recovery sites.

Which design resolves this issue?

2. An engineer must use OTV for layer 2 connectivity between data centers to support virtual machine between the customer sites. To support this requirement, the engineer must ensure the existence of the same default gateway on both sites. Additionally, the operations team report high bandwidth utilization on site A and wants to optimize the outbound traffic flows to use a DC exit point.

Which feature must be used to meet these requirement?

3. A Cisco UCS chassis with several blade servers, a pair of IOMs, and a pair of Cisco UCS Fabric Interconnects are installed in a data center.

Which two high-availability architectures are recommended between the IOMs and fabric interconnects? (Choose two.)

A. One, two, four and eight links are supported to be used between each IOM and fabric interconnect.

B. IOM is connected to the fabric interconnect that is acting as fabric

A. and IOM B is connected to the fabric interconnect that is acting as fabric B.

C. Any combination of one to eight links are supported to be used between each IOM and fabric interconnect.

D. The lOMs are connected with multiple straight and cross-connect links toward a pair of nonclustered fabric interconnects.

E. Straight and cross-connect links should be used between the lOMs and fabric interconnects to offer higher availability.

4. An engineer seeks a solution to retrieve routing information from Cisco Nexus switches. The data must be exported to a web application in a JSON or XML data format for monitoring and must be encrypted during transmission. The solution must not require extensive knowledge to support and should be simple to implement.

Which technology accomplishes these goals?

5. DRAG DROP

Drag and drop the configurations from the left onto the correct policies on the right.

6. The end users report issues with datastore reachability between the newly installed virtual machines (VMs) and the storage array. The VMs are deployed on a Cisco C-Series server, directly connected with Cisco Nexus 5672UP switches over FCoE VLAN. The data traffic on VLAN 99, which is designated as a native VLAN, reaches its default gateway, but FCoE VLAN 99 fails to access the datastore.

Which action resolves the problem?

7. DRAG DROP

Drag the appropriate from the left onto the current UDLD modes of operation on the right.

8. DRAG DROP

Refer to the exhibit.

An engineer must deploy a SAN that meets these criteria:

• The upstream director switch must be configured to minimize the number of issued domain IDs

• The access switch must aggregate multiple locally connected ports not a single uplink that shares the same domain ID as the upstream switch.

Drag and drop the port types from the right onto the boxes on the left to create a SAN topology that meets these requirements Not all port types are used Port types are used more than once

9. Which pools are used when a vNIC template is created in Cisco UCS Manager?

10. A network engineer must perform a VMM integration for the VMWare vCenter platform with the Cisco ACI Fabric. The vCenter is already installed in one of the rack servers connected to ACI leaf switches in a vPC mode.

Which type of management network must be used to integrate vCenter with ACI?

11. An engineer needs an orchestration and monitoring tool that should be used for managing the storage networks and VXLAN fabrics. The tool should also allow support built-in dashboard and real-time health summary for managed devices.

Which tool meets these requirements?

12. Refer to the exhibit A Cisco engineer is configuring a next-generation Cisco HyperFlex HX data platform with 2 x Cisco UCS 6248UP fabric interconnects. 8 x Cisco HX-Series HX240c-M4SX servers, plus 8 x Cisco UCS B200-M4 blade servers Cisco UCS 5108 blade chassis, and Cisco UCS 2204XP fabric extenders The solution is configured with HX Release 4 5(2a) using VMware ESXi 7 0 U2 After the engineer migrates all customer VMs to the new solution platform, the engineer decides to create HX Native snapshots for all the VMs The engineer performs the operation and notices that some of the VMs are not creating snapshots.

What is the most probable reason that the HX Native snapshots are not created?

13. An engineer must secure the payload traversing across the DCI. The solution must support confidentially and integrity and it must be open standard. The solution must encrypt Ethernet frames regardless of the upper layer protocol used.

Which technology must be used to support these requirements?

14. An engineer is designing a data center that uses FCIP.

How is QoS configured in this environment?

15. Which type of encoding is used on 8-Gbps links as compared to 10-Gbps links?

16. An engineer is designing a Multichassis EtherChannel topology in which two switches must appear as a single device to a third downstream switch?

Which two technologies meet this requirement? (Choose two.)

17. Which two types of service profile templates does Cisco UCS support? (Choose two.)

18. A customer attaches an additional storage appliance to an existing Cisco UCS domain, which contains 50 virtualization hosts that require fabric failover connectivity on fabric interconnect B. The interfaces are bound to a separate pin group to segregate traffic with a CoS value of 0

Which Cisco UCS Manager feature meets these requirements?

19. The network infrastructure team is beginning to automate routine tasks within the Cisco ACI fabric and is searching for the appropriate solution The solution must not require any additional software installed on the Cisco APIC Networking team members lack automation experience and prefer to use a tool that does not require in-depth programming knowledge Finally configuration within the Cisco ACI fabric is rarely modified or removed

Which solution must the team choose?

20. A company needs a solution to virtualize their legacy desktop computers. The solution must be highly resilient and able to withstand the loss of a data center site. Each compute node requires a minimum of 20 disk drives.

Which solution meets these requirements?

21. Which mode must be enabled on a Cisco UCS Fabric Interconnect to connect directly to a storage array?

22. A cloud service provider provisioned four active/active data centers in various locations within the country at 50 miles between each data center. The data centers must provide redundant network infrastructure and always be available to customers.

Which two data center design steps must be used to meet these requirements? (Choose two.)

23. DRAG DROP

Drag and drop the feature descriptions from the left onto the correct UCS Fabric Interconnect modes on the right.

24. After experiencing traffic disruptions from the failure of a single router, a customer asks an engineer to design a solution that will prevent this from occurring in the future. While examining the customer’s environment, the engineer discovers that the routers are manufactured by a variety of different vendors, and they have varying amounts of CPU and memory resources. Additionally, several of the customer’s applications require the ability to fine-tune the load-balancing parameters between multiple routers.

Which solution should be used to meet these requirements?

25. An engineer finishes the initial set up of a VXLAN EVPN network. The engineer is asked to plan for connectivity that supports redundancy and extends multiple virtual routing and forwarding domains. The requirement is to use the same default gateway addressing across all leaf switches that belong to the VXLAN network.

Which two solution must be used to meet these requirements? (Choose two)

26. An engineer is building a data center network with VXLAN EVPN. The requirement is to use multicast for the broadcast, unknown unicast, and multicast replication.

Which two VNI to multicast group mapping methods must be used to meet these requirements? (Choose two.)

27. An engineer is implementing a Cisco UCS environment The requirements for the solution are for the MAC addresses to be learned only on the server-facing ports. The use of the Spanning Tree Protocol must be avoided. Also, the engineer must have deterministic traffic handling from blades to uplink ports.

Which two settings must be selected to meet these requirements? (Choose two.)

28. What are two advantages of using Cisco vPC as compared to traditional access layer designs? (Choose two.)

29. Which two configuration methods can be used to deploy QoS to Cisco MDS Series switches? (Choose two.)

30. A network administrator must create a redundant vHBA for the mission-critical virtual machines (VMs) installed on a Cisco UCS Fabric Interconnect blade server. The VMs access multiple datastores using VSAN55 and VSAN95. The datastore on which the VMs are hosted must be accessible if any of the uplinks goes offline.

Which action meets these requirements?

31. An engineer must design Layer 2 connectivity for a subnet between two data centers. The engineer must ensure seamless host mobility and optimal first-hop routing.

Which attribute must be synchronized across all data centers to achieve this goal?

32. A company data center requires a new disaster recovery solution to host critical services. The solution can sustain several hours of data loss because the services are routinely backed up to an offsite location. Also, the disaster recovery solution must provide 24-hour availability. Due to the strict policy requirements, the company wants to retain complete control of when the failover process occurs.

Which solution meets these requirements?

33. A network engineer must select a high availability feature for their data center.

The solution must ensure network resilience, reduce network instability for Layer 3 routing protocols, and meet these requirements:

✑ The device must notify its neighbors when the control plane is undergoing a restart.

✑ The solution must suppress routing flaps in case of stateful switchovers.

Which solution must be implemented?

34. A customer deploys 32 virtualization hosts in a Cisco UCS domain. All hosts run in the same cluster and have Identical hardware specifications. The operating system requires that all firmware is consistent across the hosts (or driver support. The customer must provision additional interfaces later for expandability.

Which feature of Cisco UCS Manager meets these requirements?

35. Which type fields can an engineer use to identify an iSCSI participant? (Choose two.)

36. A cloud provider deploys an infrastructure based on Cisco ACI Fabric, Cisco UCS, and Cisco HyperFlex Data Platform. The storage area network will be based on Cisco MDS 9000 Series Switches with Hyper-V, VMware, and KVM used as the virtualization platform. The requirement is to deploy the overall solution by using a robust automation and orchestration tool.

Which tool meets these requirements?

37. A network architect needs secure access to the organization’s perimeter routers and firewalls. The administrator must access network devices from a remote location that is reachable from the WAN cloud

Which action meets these requirements?

38. An engineer working for a private telecommunication company with an employee ID 4419 90 979 is installing a pair of Nexus 7000 Series Switches and must deploy the solution with these requirements

• The environment must be separated for test and production purposes

• The separation should include control, data and management plane with fault domain isolation and improved security

• The test environment needs only F2 series line cards and a maximum of 256 VLANs

Which set of actions meets these requirements?

39. An engineer is implementing management access to a Cisco Nexus platform. The customer requires a solution that provides isolation between the data and control planes. In addition to management that uses encryption and authentication. The customer will manage the device using both IPv4 and IPv6.

Which two components should be used to meet these requirements? (Choose two)

40. An engineer must design a disaster recovery solution for a Cisco ACI Multi-Site network. One requirement is that the applications must have seamless IP addressing across sites. The solution must also be highly resilient and support Layer 2 adjacency.

Which design meets these requirements?